Tag Archive for iOS

And now for something completely different… British Gas Hive Smart Thermostat Review

Having recently had the Hive smart thermostat system installed in our house by British Gas, I’ve been asked by a handful of people subsequently as to whether it is any good, so here are a few notes to that end… being a thermostat review of course, it does have the potential to be the most boring blog post ever! With that in mind, if you have narcoleptic tenancies or have pretty much anything else to do, I suggest you stop reading now!

Installation
We didn’t get off to a great start as there were some scheduling issues with BG getting the right engineer to come and complete the fitting (not all of their engineers are currently trained to do so). That aside, the actual install was relatively quick and simple, with a minor niggle when the engineer had to contact the Hive team to reset the device and get it to make its original connection “back to base”.

The thermostat is also completely wireless (using standard AA batteries), so we we’re able to relocate it as part of the installation, into our living room. Point to note, it is ideally meant to be installed at a height of 1.5m from the floor, something which our engineer didn’t actually mention when fitting it below this height. The wireless feature is very handy though, as the location of our old wired thermostat was not ideal and this will now more accurately allow us to control the temperatures based on where we spend the most time.

Functionality
Ultimately it’s a thermostat, so functionally it simply:

  • Turns our upstairs hot water on and off on a schedule (downstairs is on demand already).
  • Turns the heating on until it reaches the defined temperature.

But, compared to a standard on/off thermostat, it also:

  • Allows different temperatures at different times of day, instead of just being based on whatever temperature your legacy thermostat is currently set to.
  • Has built in freeze protection, so even if you turn it off when you leave the house, if the temperature drops below 5 degrees, it will automatically turn on your heating; very useful indeed!
  • Geolocation – Can use your current location (via the smart phone app) to turn your heating on / off depending on whether you are in the house, or within a specified distance of it.

Usability
Between myself using the app and my wife using the wall unit for the past week I can confirm that it is fine, but the wall unit UI is not quite as intuitive as it perhaps could be. For example changing the current scheduled temp will temporarily show the desired temp, then switch back to showing the current temp. This led my wife to believing that it had not accepted her new temp! Perhaps a better UI would have been to show both temps (current and target) on the same screen in different size fonts…

I have not yet tested the Geolocation feature so won’t comment on that yet, other than that I hope Hive are not keeping a track of your location history on their systems – this is not made clear on their FAQ website and would be a bit creepy if they were!

Configurability
Temperature on the thermostat can be set to the nearest 0.5 degrees, which is granular enough for us.

The only minor bugbear I found was that the original firmware delivered was based on a 4-slot schedule. For example:

  • 0600-0900
  • 0900-1600
  • 1600-2300
  • 2300-0600

That’s all very well if you are out during the day every day or want the same temperature most of the time, but what about weekends, or even if you have young children at home during the day. The recently added functionality to the system is a 6-slot schedule. So now you can have (for example):

  • 0600-0900
  • 0900-1200
  • 1200-1400
  • 1400-1600
  • 1600-2300
  • 2300-0600

This is much more useful, particularly for heating. I have found the 4-slot schedule perfectly adequate for the hot water schedule.

Customer Service
So far my only interaction with customer services was when I posted a tweet that I could really do with the 6-slot schedule (not rolled out to everyone at this point). A very polite customer agent at Hive picked up on my tweet:

He got my account details via DM, pushed out a firmware update to my device to add the functionality, and DM’d me again to let me know when it was updated a couple of hours later. How about that for customer service?!

Performance
The app can be a little slow refreshing your current heating status and temperature at times, even on a decent 3G connection and occasionally even on wifi. Other than that it’s pretty quick and easy to use. Telling the thermostat to increase the temperature usually results in the boiler kicking in 5-30 seconds later.

Security
As I understand it, Hive uses the fast growing industry standard ZigBee protocol, which uses 128-bit AES encryption for its communication between devices.

The hub itself is apparently an AlertMe SmartHub Nano, which runs a variant of Linux. This should be reasonably secure assuming it has been locked down, and that BG provide regular security patching to the device, especially in light of recent major security issues such ShellShock. Ultimately the device does not require you to open inbound ports on your router, so assuming all comms between hub and central system are SSL encrypted as they are with the apps, then it’s no less secure than your laptop accessing a secure website over wifi.

Money Saving & Costs
It’s too soon to tell whether it has saved any real money, but I do know that with the more specific schedules than we could achieve with our old thermostat I think it is likely that it will save money. Whether we get close to the claimed £150 pa on the website, I’m not convinced, but even if it only achieves a third of that, then it should pay for itself within 3 years.

The system comes with a one year warranty. Beyond that we use British Gas HomeCare, so any issues are covered by BG as part of our service plan. If you are not using BG HomeCare, then your mileage and potential costs may vary!

Moving House
Interestingly, if you move house or move into a house which has a hub, you can still use the standard thermostat functionality and configure it using the wall unit, but you would need to buy a new hub to get the online and app features, which seems somewhat unreasonable and wasteful to me!

Conclusion
Overall I’m pretty happy with the system and I think it will likely save some money in the long run, whilst providing a more convenient experience and comfortable home. My wife is less so, but then again, she still uses a BlackBerry!

Fingers crossed it lives up to expectations and that reliability proves good over the coming months and years!

I Opened up a Can of #VUPaaS and it was Good! – Podcast Review

VUPaaS Logo

I recently had a 7 hour day in the car thought I would catch up on the first half a dozen episodes of the new VUPaaS podcast and see what it was like. The Virtualization User Podcast as a Service was started at the end of 2013 by Gurusimran “GS” Khalsa (@gurusimran), Chris “Cisco Kid” Wahl (@ChrisWahl) & Josh “Mute  you in a Heartbeat” Atwell (@Josh_Atwell) and is focussed on users of virtualisation tech.

One of the things which immediately jumped out at me about the format of the show is that there is a lot of discussion around user requirements, which as a Solution Architect, is exactly what I do all day! In that respect it is particularly interesting as the show has (to date) included a wide range of different users from different industry verticals and different backgrounds, environments etc. It’s fascinating to me to understand the reasons behind the design decisions which have been made, and how that has panned out in implementation.

Another great element of the show is the real-world hints, tips and experiences which are brought to light by the guests when they discuss the issues they came across in implementation, or for example Chris Mohn discussed some of the tools he uses to “get the job done” as a consultant. They also had our own #LonVMUG regular Ed Grigson talking about Oracle, Cloud, DevOps and everything in between.

One other type of “user” I would be interested to hear from on a show (even just a one-off), is one of the decision-maker “users”; a CTO/CIO/IT Director. It would be interesting to understand how they make their decisions and what information sources drive them to procure something that their employees then have to implement (sometimes without necessarily engaging those people in the decision making process!).

I have enjoyed the show so much to date, it has immediately jumped into my Top 4 favourite podcasts. I would definitely recommend you check it out!

My current podcast list is as follows (in order of preference):

Podcast

Published

Link

Speaking in Tech

Weekly – Wednesdays

http://speakingintech.com/

vSoup

~ Every 3-4 weeks

http://vsoup.net/

vNews

~ Monthly

http://www.stumchugh.com/

VUPaaS

~ Weekly

http://vupaas.com/

VMware Communities Roundtable

Weekly – Wednesday Evenings

https://blogs.vmware.com/vmtn/podcasts

Around the Storage Block

Irregular

http://h30507.www3.hp.com/t5/Around-the-Storage-Block-Blog/bg-p/139

Packet Pushers

Multiple per week

http://packetpushers.net/

Professional VMware Brownbag

Weekly

http://professionalvmware.com/brownbags/

GreyBeards on Storage

~ Monthly

http://silvertonconsulting.com/gbos2/

Puppet Labs Podcast

Irregular

http://puppetlabs.com/resources/podcasts

One wee tip if you want to start listening to more podcasts is to have them set to auto-download onto your Android or iPhone overnight. Then by the time you get into the car in the morning they’re ready to go! On Android I use BeyondPod for managing this.

That about wraps it up for now but just to reiterate, I highly recommend you too open up a can of VUPaaS at your earliest convenience!

%d bloggers like this: