Tag Archive for DC53427HYE

NanoLab – Part 10 – Your NUCs are nice and cool, but what about your stick?

I have been running a variety of Intel NUC nodes in my vSphere homelab over the past 3 years now, including the D34010WYKH, DC3217IYE & DC53427HYE.

In that time I have unfortunately seen more than my fair share of USB drive failures and corruptions, generally with an error which looks something like this:

Error loading /k.b00
Fatal error: 33 (Inconsistent data)

These are not cheap and nasty, or freebie USB drives, so I would not normally expect to see this rate of failures. The error only occurs when you reboot the host, and the startup bombs out at the start of the hypervisor launch. I have often managed to recover the stick by copying back corrupted files from another instance, but generally I needed to rebuild and restore the image. An unnecessary pain in the rear!

The Root Cause
The NUC case can become quite warm during normal operation with or without the fans spinning up, and I have come to believe that the main reason for the corruptions is that the USB stick itself is getting too hot and therefore eventually failing. Having pulled a USB out from a recently shut down node, they are really quite hot to the touch. You don’t actually see the symptom / failure until a reboot because the ESXi image actually runs in memory, so is only loaded from the USB stick at boot time.

The Solution
As for the solution, it’s really quite simple. I purchased a number of 12cm (5 inch) USB 2.0 extender cables on eBay for just 99p each (including delivery!).

These keep the USB stick indirectly attached to the NUC chassis, and as such the heat does not transfer into the flash drive. Since doing this I have not seen any further issues with the corruptions. Job done!

Keeping things cool: USB extender on Intel NUC

Keeping things cool: USB extender on Intel NUC

NanoLab – Part 8 – Quick Tip for Blank Screen on vPro Intel NUC

Just a very quick tip for an annoying issue I have experienced with my Intel NUC DC53427HYE and never quite found the time to look into it and find a proper fix, that is until a recent twitter conversation! Kudos and many thanks to Frank Brix Pedersen and Mads Fog Albrechtslund for finding the solution and an EU reseller, and Frank for testing and posting it on his blog site.

If you have a vPro NUC and dont connect it permanently to a screen, then when you next connect to it via the vPro remote KVM interface, you get nothing but a blank black screen.

Link to Franks post is here which explains the symptoms and fix in detail:

Frank has the NUC5i5MYHE model, but the fault looks identical to the issue I have been seeing so I will be following his post and purchasing a Fit Headless dongle from Tiny Green PC for £12 (and a rather ripoff £12 postage cost unfortunately, but there don’t seem to be any other UK suppliers). It is also available from opencompany.dk for others in the EU.

I will update this post once I have tested it on the DC53427HYE!


NanoLab – Part 6 – Keeping Your NUCs Cool (Quick Tip)

Just a very quick tip I discovered this weekend.

If you are using your Intel NUCs with any anger, they will likely run reasonably hot to the touch and typically you would just place them horizontally on a surface as per the pictures above. For optimum performance and lifespan, we all know it’s always important to keep your NUCs as cool as possible!

The NUCs are also designed to be mounted vertically on the back of a monitor/stand/wall/desk or similar, using the VESA mount. What I didn’t realise is that whether mounted or not, if you run them on their side, they seem to actually maintain lower temperatures.

I’m not sure if the same would apply for the newer generation of NUCs with the 2.5″ drive cages, which also have small vents down the side, but it certainly works on the standard models.

Vertical running of NUCs

Vertical running of NUCs

This seems to work pretty well for me, but as always, I take no responsibility if your NUC explodes with the fire of a thousand suns!

That is all.

%d bloggers like this: